Frequently asked questions
A few answers before your next exploration.
Using the tools
How do I choose a point?
Click or tap the globe or map. Drag the globe to rotate it; dragging does not add a point. You can also enter decimal latitude and longitude. On the focused globe, arrow keys rotate and Enter selects its centre.
How do I move around the detailed map?
Drag to pan on desktop. On touch devices use two fingers to move the map so one-finger page scrolling stays available. Use the plus and minus controls to zoom. Draggable pins let you adjust measurements.
Are my measurements saved?
Switching tools or globe/map views keeps each measurement in the current page. Most tools also put their inputs in the page address, so reloading, a bookmark or a shared link reopens the same result; there is no account or cloud save, and clearing a measurement removes it from the address. Random Location separately remembers visited destination identifiers in your browser’s tab session to reduce repeats.
Does Random Location cover every place on Earth?
It alternates prepared stories with random points when both are available. With no filter, about one in ten random points is in open water. Land points use the nearest town or city in the bundled GeoNames list. Country and ocean names are approximate.
Measurements and coordinates
How does the halfway point work?
Choose A and B in Halfway Point. M is halfway along their shortest spherical surface arc, with equal distances to both endpoints. It may be in water or inaccessible; it does not calculate equal driving times. Opposite points have no unique midpoint, so move either endpoint to get a result.
What does the bearing calculator show?
Choose A and B in Bearing Calculator. The initial bearing is the compass direction to start out in at A to follow the shortest surface arc to B; the final bearing is the direction of that arc as it arrives at B. Both are measured clockwise from true north, not magnetic north, and are not road directions. Identical or opposite points have no unique bearing.
What does the destination point calculator do?
Choose a start in Destination Point, then enter a bearing and a distance. It finds where you end up travelling along the shortest surface arc, and shows the bearing on arrival. Bearings are measured from true north, not magnetic north, and the path is not a road, flight or sailing route. A bearing has no meaning at a pole, so start a little way off it.
Which coordinate formats can the converter read?
Coordinate Converter reads decimal degrees, degrees-minutes-seconds, degrees with decimal minutes, UTM, MGRS, full Plus Codes and geohashes, and shows the same location in all of them. Everything uses the WGS 84 datum, so grid references from other datums will land in the wrong place. UTM and MGRS are not defined above 84° N or below 80° S.
How accurate are the sunrise and sunset times?
Sunrise & Sunset uses the NOAA solar equations, accurate to about a minute at most latitudes. It ignores hills, buildings and your height above the ground. Times show in UTC unless you choose another zone; the tool does not know which zone a place is in. Inside the polar circles it reports midnight sun or polar night instead of times.
Are the measurements exact?
They are estimates on a spherical Earth with a mean radius of 6,371.0088 km. Distances follow shortest surface arcs, without terrain, roads or journey times. They are useful for exploration and comparison rather than surveying or navigation.
How do I finish an area boundary?
Add at least three distinct vertices in boundary order, then select Finish boundary. Do not add the first vertex again. You can drag or remove vertices after closing, or select Edit boundary to add more. Undo reopens the boundary. Up to 50 vertices are supported.
Why is an area boundary rejected?
Crossing or overlapping edges, repeated points, collinear or very small boundaries, and antipodal edge endpoints can make the result ambiguous or unreliable. Move or remove vertices. Area always measures the smaller enclosed spherical region, regardless of the order’s direction.
What do decimal and DMS coordinates mean?
Latitude comes first and longitude second. Decimal output uses six decimal places. DMS means degrees, minutes and seconds, rounded to whole seconds with N/S and E/W for direction. Coordinate Finder can copy either format.
Why can I not see both antipode pins on the globe?
Only one hemisphere is visible at a time, and antipodes are opposite points. Use Show original or Show antipode to turn to the chosen point. The tool does not invent a unique connecting route.
Maps, data and privacy
How do I contact TrindoMaps?
Use the contact form for a question, problem report or privacy request. Your message is emailed to TrindoMaps through Resend, without adding you to a mailing list. Include an email address so TrindoMaps can reply.
Why does a map fail to load?
Detailed maps need a network connection, a browser with WebGL and an available map provider. Coordinate entry and browser calculations remain usable when maps fail.
Does the site ask for my current location?
Only if you ask it to. Select points yourself or enter coordinates. The My location button on the detailed map and the Start from my location button on the Distance Calculator ask your browser for permission when you press it; the app does not send the position anywhere. Like any point you choose, it can appear in the page address; see the Privacy Policy.
Do map providers receive any information?
Yes. Displaying detailed maps sends style, font and tile requests directly to OpenFreeMap. Those requests reveal the viewed map area and include network/browser information. Read the map-request section of the Privacy Policy for details.
Can I reuse the maps, stories or photos?
Each source keeps its own licence. Check the visible attribution and Credits & licenses notice before reusing content. A free tool does not make all underlying content public domain.
Ready to try one? Open the Distance Calculator or browse all sixteen tools.